This Directions sheet is supplied separately so that it cannot become damaged as a result of spills or drips while using our paint remover/stripper. Keep it away from the immediate working area. 

DIRECTIONS 
Remove all plastic materials and other items such as lenses, mouldings, windshield wipers, grills, mirrors, chrome, etc. When stripping door jams, remove soft rubber or cover it with masking tape before spraying. 

When stripping an entire automobile or boat, begin high and do small sections at a time. Work in a well-ventilated area where temperature is above 50 degrees and below 95 degrees. Do not work in direct sunlight or under windy conditions. Surface to be stripped should be cool, not hot. An open garage will provide the best working conditions. 

Contains Methylene Chloride. May irritate skin. Contact with flame or hot surface may produce toxic gases. 

APPLICATION PROCEDURE 

1. Spray on a full wet coat, but avoid running or dripping. Let it set for 15 minutes if surface was enamel, or 5 minutes if surface was lacquer. 
2. Apply a second coat over the first and permit to set for another 15 minutes (enamel surface). For lacquer finishes, move to step 3. 
3. Remove the stripped finish using a plastic spreader or other suitable tool. Re-spray surface with stripper and wash, using steel wool and water to final clean the surface. Wash from the bottom up on each panel. Use water only, as soap may leave a residue or film. 

POR-15 Paint Remover/Stripper WILL damage or remove the following:
Tile, Linoleum, Asphalt, Plastics, Synthetics, Sheet Rock, Paper, Wicker, Bondo & other body fillers, 

* If rubber soaks in stripper for an hour or more it may temporarily lose its shape; however, if subsequently washed with water and permitted to dry it will return to original shape. 

** Stripper will remove natural oils from leather, but these can easily be replaced with leather lubricants, tung oil, saddle soap, hide food or other similar products. 
 

When Stripping:

Imron: apply two full coats, waiting 10 minutes between coats. 

GM Black Primer: remove topcoat first, then spray one full coat, wait 5-10 minutes, then wash with #2 steel wool and water. 

Baked Enamel: spray one full wet coat, wait 10 minutes and spray a second coat over the first without removing any paint. Wait 10 minutes and remove with scraper. Lacquer, spray a full wet coat, wait 5-10 minutes and lacquer will melt off. Use plastic scraper to remove. 

Polyurethane: spray a full wet coat, wait 20 minutes and remove. 

Wood: wash off stripper with wood alcohol, denatured alcohol, or methanol...Shelf Life is up to 6 months in an unopened bottle, but it is recommended that product be used as soon as possible after purchase. 

SHAKE WELL BEFORE USING 

CAUTIONS:
Keep away from heat, sparks, or open flame. Keep container closed when not in use. Do not take internally. Contact with flame or hot surface may produce toxic gases. Use of goggles and gloves is strongly recommended to avoid skin contact or accidental contact. Store away from heat and out of direct sunlight. Open can slowly to release pressure. If skin contact is made, wash immediately with soap and water. Avoid prolonged breathing of vapors. 

Use only with adequate ventilation. Persons with known respiratory or heart ailments should exercise extreme caution when using Methylene Chloride-based products. Avoid exposure to fumes or vapors. 

KEEP OUT OF THE REACH OF CHILDREN 

FIRST AID: 
If swallowed, call physician, hospital emergency room or poison control center immediately for instructions on inducing vomiting. DO NOT USE table salt solution. If possible, give one tablespoon of Ipecac syrup and one glass of water. Patient should lie down, keep warm, cover eyes to exclude light. 

FOR EYE CONTACT: Flush repeatedly with water. 

FOR SKIN BURN: Apply petroleum jelly to skin. 

Information contained herein is to our knowledge true and accurate, but all recommendations or suggestions are made without guarantee. Since the conditions of use are beyond our control, POR-15, Inc. disclaims any liability incurred in connection with the use of its products and information contained herein. No person is authorized or empowered to make any statement or recommendation not contained herein, and any such statement or recommendation so made shall not bind The Corporation. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing patents covering any material or its use, and no license implied or in fact is granted herein under the claims of any patents.